নলেজ লাইব্রেরি

This document describes an indicator that plots two selected momentum or rate of change series in one chart window, allowing comparison across indicator types and lookback periods. It lists five variants: Momentum, Rate of Change, Rate of Change Percentage,…

This MetaTrader expert advisor follows a time-based routine using the Color3rdGenXMA moving average. At a specified hour and minute, it checks the indicator color and opens a short position for red or a long position for blue. It closes the position after a…

This expert-advisor description combines a 150-period moving average with short-period RSI and Stochastic readings. Price relative to the moving average sets the permitted direction: above it, the system considers buys; below it, sells. A buy requires RSI…

This document describes an Expert Advisor that trades signals from the Digital CCI Woodies indicator. A signal is generated when a bar closes and the indicator’s cloud changes color. The page also notes that the compiled indicator file must be installed in…

This indicator combines a MACD calculation with two stochastic normalization stages and exponential smoothing. It first computes MACD as the difference between fast and slow exponential moving averages of the selected price. That value is scaled within its…

This indicator example applies spectral filtering to a moving average time series. It removes higher-frequency components from the series to produce a smoothed output, and the description says the technique has practically zero latency. It presents the…

The document explains the classic Coppock indicator as a long-horizon signal for potential buying or selling opportunities. Its calculation adds two rates of change, using lookback periods of 14 and 11, then applies a 10-period weighted moving average to…

The document outlines a basic automated strategy that buys when the Relative Strength Index is oversold and sells when it is overbought. It describes the logic at a high level and says the expert advisor can be used with MetaTrader 4 or MetaTrader 5 after…

The document describes an indicator that displays a forex price chart in inverted form, intended to help traders consider short entries when their usual bias is toward long positions. Its suggested workflow is to add the inversion indicator to a chart and…

PAC, or Periods After Crossing MA, is an oscillator that tracks the number of bars since price most recently crossed a moving average. Its histogram is positive after an upward crossing and negative after a downward crossing. While price remains on the same…

This document describes a version of the Three Candles indicator with a configurable chart period. The timeframe input lets a user select the period from which the indicator draws or calculates its signals, with a four-hour period set as the default. This…

KhaosAssault presents price movement as a point-based chart with marked levels for significant changes. The description identifies the indicator as a MACD histogram and says it uses configurable fast and slow moving-average parameters. This makes it a way to…

This indicator description defines an advance-decline measure over a chosen period by subtracting the count of bearish candlesticks from the count of bullish candlesticks. It offers two modes. In non-cumulative mode, the displayed value is the difference for…

This indicator note explains how Average True Range is built from True Range, defined as the greatest of the current high-low range and the absolute gaps between the current high or low and the previous close. It describes an initialization step that…

The document outlines an Expert Advisor that uses the non-normalized FatlSatlOsma oscillator. It makes a trade decision when the oscillator changes direction, and is presented for use in MetaTrader 5 with the corresponding compiled indicator file. A…

This indicator description presents a simple rule that combines Williams %R and the Relative Strength Index to mark chart signals. It describes averaging a shifted Williams %R reading with a short-period RSI reading, then comparing the result with the…

The document explains the Count Back Line (CBL) as a short-term trend confirmation and entry tool, intended to be used after other signals suggest a possible reversal. It describes combining CBL with trend lines and the Guppy Multiple Moving Average to…

The document describes a MetaTrader example for retrieving the highest and lowest bar prices over a specified interval covering the previous 24 hours. It identifies keyboard shortcuts for searching for the high or low, and says the example uses the…

The document describes a band indicator that varies Bollinger Bands and Envelopes. It builds the bands from two smoothed moving averages calculated with the linear regression moving average method (LSMA). The two configurable inputs are the LSMA calculation…

This utility finds the maximum high and minimum low within a user-selected range of chart bars. The user specifies a start bar and an end bar; the procedure identifies the candle with the highest high in that interval and returns that high. It performs the…

The indicator identifies a completed candle that crosses a moving average and locates the preceding crossing. It draws a rectangle spanning the bars between those two events. The rectangle’s upper and lower boundaries are presented as possible take-profit…

The document describes an indicator called AIS Central Axis that applies a nonlinear smoothing algorithm related to the HiLo family. It distinguishes the method from the classical version by processing extrema in the input time series. The stated parameter…

The document describes a forex cross-pair setup using a correlation calculator panel to compare a cross with its two component currency pairs. Its example considers EUR/JPY alongside EUR/USD and USD/JPY. The proposed signal is a change in which component…

This short description explains basic controls for a 3D moving average indicator. It offers two color modes: one varies with price, while the other changes according to the moving average period. Users switch modes with the C key and adjust the step between…